Wilson SignalBoost DB Pro Amplifier Omni Ant/Cbl Kit

In Building Cellular Repeater System

The Wilson SignalBoost DB Pro DualBand in-building cellular repeater greatly improves signal strength for any cellular device inside a building on most networks. It does not require any physical connection to your phone allowing you to walk around freely during a call. It even allows multiple cell phones and/or Data Cards to be used simultaneously. Using the omni directional antenna included in this kit will capture the signal from multiple towers & service providers in the area. Separation requirement between the inside and outside antenna is 50 ft (inside panel antenna should be mounted so that it is pointed away from the outside antenna.)

Adjustable Gain

The gain on the SignalBoost DB Pro is adjustable in 5db increments up to 62db for 800MHz and 65db for 1900MHz. Being able to adjust the amplifier gain makes installation easier in situations where there might be a challenge getting enough separation between the inside and outside antenna.

IMPORTANT NOTE

Requires at least 50 feet of separation (25ft if using directional outside antenna) between Inside and Outside Antenna Requires fairly good signal outside (2-3 bars min.). The better the outside signal, the more cellular coverage inside the building. See below for estimating improved coverage area. All components are interconnected using standard TV cable (RG-6) which is easily available and often found pre-installed, simplifying cable runs.

Coverage Area & Installation Information:

• Estimating Improved Coverage Area.
• SignalBoost DB Pro Installation Doc

Kit Includes:

• Wilson SignalBoost™ DB Pro™ Amplifier (801262)
• 6 volt AC/DC Power Supply
• Instruction Manual
• Wilson Omni Directional 75 Ohm Building Mount Antenna with mounting hardware. (301201)
• Wilson Dual Band 75 ohm Panel Antenna (301155)
• RG-6 Quad Shield Coax Cable:
  • 1 ea. - 20’
  • 1 ea. - 30’
  • 1 ea. - 50’
  • 1 barrel connectors F-female to F-female to combine lengths.

Surge Protector

Optional Wilson Lightning Surge Protector AM859988 recommended (not included).

Antennas Included

Wilson Panel Antenna

The Wilson Panel antenna is typically used as an indoor antenna and is wall mounted but can be ceiling mounted on higher ceilings (10ft or higher). They work well across longer, more narrow areas. Since they typically reach further, they are the prefered inside antenna. The Panel antenna radiates 70 degrees for a more focused beam to reach longer distances. More Panel Antenna Information

Building Mount Omni Directional Antenna

Wilson Building Mount Omni-Directional Antenna covers 800/1900MHz frequencies. It is omni-directional. If you are trying to boost the signal from several service providers where their towers are in different directions, this is the preferred antenna. If you are trying to cover one service provider tower, consider the higher gain Wilson Wide Band Directional Antenna. More Wilson Building Mount Omni Directional Antenna Information

About Building Cellular Amplifiers

The Wilson DB Pro In Building Cellular Amplifier Repeater is a small, bi-directional amp that deliver service levels consistent with what would be expected in areas of high cell network coverage. They amplify a weak or shadowed cellular signal and repeat it in an in-building application. When using a Wilson amplifier in conjunction with Wilson antennas, the outside antenna will collect the cell tower signal and send it through the cable to the amplifier. The signal is then amplified and broadcast from the inside antenna to the surrounding area.

Cellular Amplifier for use in Homes, Fire Stations, Command Posts, Offices and Other Buildings.

Cell phones and cellular data cards in that area then communicate with the improved signal. When a cell phone or cellular device transmits, the signal is received by the inside antenna, amplified by the amplifier and broadcast back to the cell tower through the outside antenna.

Wilson DB Pro Cellular Amplifier Features:

• Has up to 20 times more power than your cell phone or laptop data card
• Significantly improves voice and data signal quality
• Improves data communication rates needed for 3G Technologies
• Uses commonly installed and available 75 ohm RG-6 Cable
• Wireless operation. No physical connection to your phone is required.
• Powerful 65db Gain For 800 MHz Cellular and 1900 MHz PCS Bands
• Works on all generations of CDMA, TDMA AND GSM Including AT&T, Sprint, T-Mobile, Verizon, etc. (Not for Nextel iDen Networks. See iDen Cellular Repeaters)
• Automatic gain adjusting to prevent oscillation
• Gain Indicator lights
• Automatic shutdown on overload
• Cell site friendly design
• FCC and Industry Canada type accepted

Wilson DB Pro Cellular Amplifier / Repeater Specifications

• Frequency 824-894 MHz / 1850-1990 MHz
• Adjustable Gain (Max Up/Down 62 dB @ 800 MHz / 65 dB @ 1900 MHz
• Flatness +- 5 dB
• Max Output Power 2.5 Watts
• Max RF (Up/Down) + 34 dBm / + 15.7 dBm
• Noise Figure (typical) 3.5dB nominal
• Isolation > 90 dB
• Power Requirements 120 - 240V AC, 50-60 Hz, 8 W
• Connectors F-Female
• Dimensions 6.2 x 4.2x 1.5 (inches) 15.7 x 10.7 x 3.8 (cm)
• Weight .64 lbs / 0.29 kg

Wilson Electronics 75 Ohm Building Antenna Specifications

• Frequencies: 806-894 MHz / 1850-1990 MHz
• Impedance: 75 ohm
• Polarizaton: Vertical
• Gain: 5.12 dBi (806-894MHz) / 6.12 dBi (1850-1990 MHz)
• Max power: 25 Watts
• Beamwidth Horiz Pln: 360 deg
• Beamwidth Vert Pln: 60 deg
• VSWR: 1.8:1
• Connector: F Female
• Dimensions: 14.5 inches
• Ground Plane: Built-In Ground Plane
• Part #: 301201

75 Ohm Panel Antenna Specifications

• Frequency Ranges: 
•     700 - 800mHz ... Gain: 5.2dbi
•     824-894MHz ... Gain: 4.4dbi
•     880-960MHz ... Gain: 4.2dbi
•     1710-1880MHz ... Gain: 10.0dbi
•     1850-1990MHz ... Gain: 10.6dbi
•     2110-2170MHz ... Gain: 8.2dbi

• Nominal Impedance: 75 Ohms
• Beamwidth in Hor. Plane: 70°
• Beamwidth in Ver. Plane: 50° / 45°
• F/B: >=20 db
• Polarization: Vertical
• VSWR: <= 1.5:1
• Ground Plane: Built in Ground Plane
• Dimensions: 8.27 x 7.09 x 1.73in or 21 x 18 x 4.39cm
• Weight: 1.32 lbs or .6 kg
• Cable Length: 6 in.
• Connector: F Female
• Part #: 301155