Wilson Electronics 900MHz 60db SmartTechnology Building Amplifier
Use this Wilson building amplifier for 900MHz iDen (Nextel) Networks and 900MHz GSM (mostly found in parts of Europe, Asia, Middle East, etc).
Eliminate Dropped or Missed Calls Speed Up Cellular Data Transmission
Do you have a good cellular signal outside your building but little to no signal inside the building? This Wilson 900MHz Smart Technology In-Building cellular amplifier works by picking up a stronger signal outside, amplifying the signal then rebroadcasting the cell signal inside the building. The amplifier uses an outside antenna mounted on a pole or wall outside your building and an inside antenna. This Nextel cellular amplifier increases the signal and transmits it through the inside antenna to your cell phone or laptop data card.
- Amplifies 900MHz Frequencies (iDen and GSM)
- Wireless operation. No physical connection to your phone is required.
- Automatic Gain Adjusting in the event of oscillation and /or overload
- Automatic shutdown on overload
- TIA/EIA-98-E 3.5.1 Receiver Sensitivity better than -110 dBm
- Allows multiple phones to be use simultaneously.
- Your phone will use less battery power for longer battery life.
- Requires Outside Antenna, Inside Antenna and Cable (Not Included)
To cover 900MHz frequencies, use these antennas:
Improves signal coverage area for:
- iDen 900MHz frequencies including Nextel.
- 900MHz GSM (outside US)
Important Nextel Frequency Change: Frequencies in some Nextel areas inside the US are changing to 900MHz. If you're building is in Nextel's 900MHz area, use this amplifier. For 800MHz iDen Frequencies, use Wilson 800MHz iDen amplifier. More Information on Nextel Frequency Change
Wilson's Building Amplifiers offer exceptional performance without causing harmful interference to the cell site.
Wilson Electronics’ non down-converted bi-directional iDen amplifiers are the most technologically advanced cellular amplifiers on the market today. Their most important feature is patented oscillation shutdown protection, which activates complete shutdown within just a few milliseconds to prevent harmful interference to cell sites. Wilson amplifiers also offer completely adjustable software-controlled automatic gain control, both on forward and reverse links, which allows the amplifiers to meet iDen and GSM requirements. The amplifiers are invisible within iDen and GSM systems. They also have the capability of following base station power requests which allows maintaining the full power dynamic range of the cell phone.
Antenna Separation Requirements (Important)
A building amplifier system requires at least two antennas (not included). One antenna for outside and one for inside. The outside antenna must be a certain distance away from the inside antenna. IMPORTANT: The distance must be actual distance between the inside and outside antennas not just cable length. This amplifier requires at least 75 feet apart (50 feet if roof is constructed of metal or heavy concrete) of separation between the inside and outside antenna. Do not turn on your iDen cellular amplifier unless you have at least the above distances between the inside and outside antenna. These distances must be maintained or the signal will just oscillate between the two antennas and no improvement will be noticed. Also, not enough separation can damage the amplifier.
- Frequency 900MHz iDen or GSM
- Gain 60 dB max
- Max Output Power: Up to 3 watts
- Max RF + 30 dBm uplink / +30 dBm downlink
- Noise Figure 3 dB nominal
- Flatness ± 2.5 dB
- Isolation > 90 dB
- Power Requirements 120 V AC / 3 A max
- Connectors N-Female
- Dimensions 5.6 x 3.6 x 1.7 (inches)
- Weight 1.5 lbs or 0.7 kg
Building cellular amplifier for Nextel iDen 900MHz and 900MHz GSM (Europe, Asia, Middle East) networks. 60dB Wilson Smart Technology™ Bi-Directional in bulding signal booster.
You may also be interested in the following product(s)
As low as: $616.41
|Connector Type||N Female|
|Frequency Range||900 MHz|
|Accessory Type||Signal Improvement|