Wilson SignalBoost™ DB Pro™ Cellular Amplifier

Wilson SignalBoost™ DB Pro™ In Building Cellular Amplifier

$459.95
MSRP: $559.95

Comes with

• Wilson SignalBoost™ DB Pro™ Dual Band Cellular Amplifier
• 6 volt AC/DC Power Supply
• Instruction Manual

Requires inside and one outside 75 ohm antennas plus 75 ohm RG6 coax cable (not included). Antenna connectors on the amplifier are F Female (requires 75 ohm Quad Shield RG-6 coax cables with F Male connectors), View Specifications. 801262

Works for most 800MHz and 1900MHz range networks including CDMA, TDMA, GSM within the US and Canada. Will Not work for Nextel iDen or Telus-Mike iDen Networks. See Wilson iDen Cellular Repeaters.) Requires at least 50 ft of separation between the inside and outside antenna.

About Building Cellular Amplifiers

The Wilson DB Pro™ In Building Cellular Amplifier Repeater is a small, bi-directional amp that deliver service levels consistent with what would be expected in areas of high cell network coverage. They amplify a weak or shadowed cellular signal and repeat it in an in-building application. When using a Wilson amplifier in conjunction with Wilson antennas, the outside antenna will collect the cell tower signal and send it through the cable to the amplifier. The signal is then amplified and broadcast from the inside antenna to the surrounding area.

Cellular Amplifier for use in Homes, Fire Stations, Command Posts, Offices and Other Buildings.

Cell phones and cellular data cards in that area then communicate with the improved signal. When a cell phone or cellular device transmits, the signal is received by the inside antenna, amplified by the amplifier and broadcast back to the cell tower through the outside antenna.

All components are interconnected using standard TV cable (RG-6) which is easily available and often found pre-installed, simplifying cable runs.

Wilson DB Pro™ Cellular Amplifier Features:

• Has up to 20 times more power than your cell phone or laptop data card
• Significantly improves voice and data signal quality
• Improves data communication rates needed for 3G technologies
• Uses commonly installed and available 75 ohm RG-6 Cable
• Wireless operation. No physical connection to your phone is required.
• Powerful 62db Gain For 800 MHz Cellular and 1900 MHz PCS Bands
• Works on all generations of CDMA, TDMA AND GSM Including AT&T, Sprint, T-Mobile, Verizon, etc. (Not for Nextel iDen Networks. See iDen Cellular Repeaters)
• Automatic gain adjusting to prevent oscillation
• Gain Indicator lights
• Automatic shutdown on overload
• Cell site friendly design
• FCC and Industry Canada type accepted

IMPORTANT NOTE

Requires at least 50 feet of separation (25ft if using directional outside antenna) between Inside and Outside Antenna

Requires fairly good signal outside (2-3 bars min.). The better the outside signal, the more cellular coverage inside the building. See below for estimating improved coverage area.

Read: SignalBoost DB Pro Installation Guide

Estimating Improved Cellular Coverage Area

Coverage area (distance from inside antenna that you can expect a usable cellular signal) can be approximated by:

1. Getting a Received Signal Strength Level (RSSL) reading using your cell phone from outside the building. You should also use the reading to determine the best location for the outside antenna. Use the pdf document "Standard Phone Test Modes " which has instructions for putting a cell phone into test mode and reading Received Signal strength. If your phone is not listed in this document or you need additional help getting a RSSL reading, contact Wilson Electronics tech support for help at 866-294-6996.
2. Estimating length and type of cable required to install inside and outside antennas
3. Selecting inside and outside antenna type.
4. Using Wilson's Online Coverage Calculator.
   1. Use 801106 60db for "Amplifier Gain" for 800MHz coverage calculations.
   2. Use 801306 60db for "Amplifier Gain" for 1900MHz coverage calculations.

NEED HELP?
If you need assistance in calculating the coverage area, call or email us after getting a Received Signal Strength Level reading and estimating cable lengths required to mount inside and outside antennas and we will be happy to help.

Repeater Antenna Requirements

The Wilson SignalBoost DB Pro cellular amplifier requires two 75 ohm antennas. One antenna for outside and one for inside. The outside antenna must be 50 feet away from the inside antenna (that's physical separation between the inside and outside antenna not cable length).

These distances must be maintained or the signal will oscillate between the two antennas and no improvement will be noticed. Also, not enough separation can damage the amplifier.

The Wilson 75 ohm Panel Antenna, or Wilson 75 ohm Dome Antenna is recommended for inside use and the Wilson 75 ohm Building Antenna or Wilson WideBand "Wedge" directional antenna is recommended for outside use.

IMPORTANT NOTE: The Wilson SignalBoost DB Pro cellular repeater is used in locations where the signal from your service provider is strong outside a building but weak inside the building. It's used where the wireless signal is blocked by the building walls or roof. If your signal is very weak outside of your building, consider a power booster or antenna that connects directly to your phone (such as Wilson's DirectConnect) for better results.

Patents Pending

Wilson DB Pro Cellular Amplifier Accessories

Wilson "Wedge" Wide Band Directional Antenna - 75 ohm

Wilson’s Wide Band Log Periodic Directional 75 ohm Antenna (800 MHz - 2500 MHz) will collect the cell tower signal and send it through the cable to an amplifier, cell phone or cellular data card. When the cell phone or cellular data card transmits, the signal is transferred to an amplifier or directly to the antenna and broadcast back to the cell tower.

More Info: Wilson "Wedge" Wide Band Directional Antenna

Wilson 301151 75 ohm Dual Band Ceiling Mount Dome Antenna

$49.95

Radiates downwards. More 75 ohm Dome Antenna Info

• Antenna Gain: 2.5dbi
• Beam Width Horizontal: 360 degrees
• Beam Width Vertical: 120 degrees
  

Cable
Cable is NOT included with this antenna. Use RG-6 Cable with F Male connector. Item: AE301151.

Dome Antenna In-Ceiling Mount

$12.95

Mount your Dome antenna above the ceiling wall between ceiling joist with this In-Ceiling mount. Includes mounting plate, screws and installation instructions. Dome antenna not included. AM901125

Panel In-Wall Mount

$29.95

Mount your Panel antenna inside a wall. Front panel is removable after installation. Features paintable cover.

Mount, Installation Instructions with mounting template, screws. Color: Cream.
Dim: 10-1/4" x 8-3/4" x 2-3/4" Deep. Wall Cut Out: 8-1/8 x 9-1/2. Panel antenna not included. 901123

RG-6 Coax Cable Quad Shield 75 ohm

Extension cables for Wilson DB Pro Cellular Amplifier. This high quality RG6 coax cable is quad shielded and 75 ohm and comes with an F Male connector on each end.

• 2' RG-6 Coax - $5.95 - White - 950602 ADD TO CART
• 20' RG-6 Coax - $9.95 - White - 950620 ADD TO CART
• 30' RG-6 Coax - $14.95 - White - 950630 ADD TO CART
• 50' RG-6 Coax - $19.95 - White - 950650 ADD TO CART

Wilson 2 Way Antenna Splitter 700MHz - 2300MHz - F Connectors

Price: $74.95

The Wilson 2 Way Splitter allows you to connect 2 internal antennas to the Bi-Directional Amplifier. Note that the signal will be split in half between the antennas. The ends on the splitter are all "F" type female so antenna cable require "F" type male connectors or adapters commonly used with RG-6 cable. Can be used with 800MHz or 1900MHz systems. Range 700MHz to 2300MHz. 859959

Lightning Surge Protector

Wilson's Surge Protectors are gas surge arresters designed to protect sensitive electronic equipment such as a power booster or repeater system from damage due to excess voltage for currents generated by transient phenomena (lightning or static build-up).

• N-Female Connectors
• Weather-proof
• Attenuation <0.2 dB
• Frequency range up to 3 GHz
• Replaceable gas discharge element
• More Information

Price: $74.95
Use with N-Male / F Female connector (Below) to tie in surge protector to your setup.

Cable Adapters

To patch in Lightning Surge Protector with with RG-6 Cable with F Male connectors. 2 are required.

N Male / F Female Connector
$8.95
AC971128

Wilson DB Pro Cellular Amplifier / Repeater Specifications