Product Description
AG Pro 70 Cellular Signal Booster from Wilson Electronics
The Wilson Electronics AG Pro 70 is an In-Building, dual band, cellular signal booster. It is an easy to install signal amplifier that is designed to provide a strong cellular signal inside mid sized buildings.
Adjustable Gain - 800/1900MHz
One challenge of in-building signal booster installation is getting enough separation between the inside antenna and outside antenna to prevent oscillation between the two antennas. Oscillation will prevent the system from working properly. In a small building, for example, that has a good outside signal, it may be difficult to get 50-75 feet of antenna separation required to prevent oscillation. With a Wilson adjustable gain amplifier, you can adjust the gain down.
The AG Pro 70 delivers a maximum gain of 70dB at 1900 MHz and 70dB at 800 MHz. The gain can be adjusted from 40db to 70db For 1900MHz frequencies and 35db to 65db for 1800MHz frequencies.
The AG Pro 70 also includes Wilson’s patented automatic oscillation and cell site overload protection, and proximity detection technologies to prevent interference on the cellular network. It works with all cellular devices on all North American service provider networks on 800MHz and 1900MHz frequencies (except Nextel/iDEN).
Additional Equipment Required
For a compete system installation, you'll need:
- Inside Antenna - 75ohm
- Outside Antenna - 75ohm
- Cable - RG-6 Quad Shield / F Male connectors
- Lightning Surge Protector Recommended
READ: Calculating Coverage Area
Surge Protector
Optional Wilson Lightning Surge Protector AM859988 recommended (not included).
AG Pro 70 FEATURES
- Adjustable Gain Control
- Provides Reliable Signal
- Significantly Reduces Dropped Calls
- Increases Cellular Broadband Data Rates
- No Physical Connection to Cell Phone or Data Card Required
- Allows Multiple Phones & Cellular Data Cards to be used Simultaneously
- Oscillation (or interference) Detection & Automatic Shutdown with Auto Reset
- Overload Protection Circuit – protects cell towers from being overloaded
- Bi-directional Signal Booster Amplifies Send & Receive Signals
- Compatible with all cellular devices on all North American cellular networks (except Nextel/iDEN)
- Configurable with a variety of Wilson cellular antennas to fit virtually any building installation
- Extends battery life – Booster enables phone to work at reduced power
- FCC and IC type accepted
AG Pro 70 Specifications
| Frequency | 824-894MHz | 1850-1990MHz |
| Gain | 65db | 70db |
| Power Output for Single Cell Phone (Uplink) | 30.8 dBm | 30.5 dBm |
| Power Output for Single Received Channel (Downlink) | 26 dBm | 25.2 dBm |
| Noise Figure | 3.5 dB Nominal | |
| Isolation | >90 dB | |
| Power Requirements | 110-240 V AC, 50-60Hz, 8 W |
|
| Antenna Connectors | N Female with F Female Adapters |
|
| Antenna Impedance | 75 ohms | |
| Dimensions | 5.7in x 4.2in x 1.5in | |
| Model Number |
271265 |
|
You may also be interested in the following product(s)
Wilson AG Pro 70 Building Cell SignalBooster Bundle KitAs low as: $731.26 |
Additional Information
| SKU | AP801265 |
|---|---|
| Brand | Wilson Electronics |
| Model | 801265 |
| Connector Type | N Female w/ F Female Adapters |
| Frequency Range | 824-894MHz / 1850-1990MHz |
| Gain | Adjustable 35-65db 800MHz / 40-70db 1900MHz |
| Antenna Category | Amplifiers |
| Accessory Type | Signal Improvement |
| GTIN | 813986010068 |
| Compatible Devices | No |
Check items to add to the cart or select all
You have no items to compare.
