Wilson AG Pro 70 Building Cellular Booster Kit

Build Custom AG Pro 70 Cellular Signal Booster System

The Wilson Electronics AG Pro 70 is an In-Building, dual band, cellular signal booster. It is an easy to install signal amplifier that is designed to provide a strong cellular signal inside mid sized buildings.

Select Equipment Required To Build Your Custom System

For a compete system installation, you'll need:

• Wilson AG Pro 70 Signal Booster
• 1 Inside Antenna - Panel or Dome
• 1 Outside Antenna - Directional or Omni Directional
• Cable - RG-6 Quad Shield / F Male connectors

Optional Accessories

• Wilson Lightning Surge Protector  (Recommended )
• 2 Way Splitter AM859959 - For multiple Inside Antennas
• Wall Panel Door Mount
• Dome Antenna Mount
• F Female / F Female Connector (for combining cables).

READ: Calculating Coverage Area

Antenna Options

Wilson Panel Antenna

The Wilson Panel antenna is typically used as an indoor antenna and is wall mounted but can be ceiling mounted on higher ceilings (10ft or higher). They work well across longer, more narrow areas. Since they typically reach further, they are the prefered inside antenna. The Panel antenna radiates 70 degrees for a more focused beam to reach longer distances. More Panel Antenna Information

Wilson Dome Antenna

The Wilson Dome Antenna is typically ceiling mounted. The Dome antenna radiates 360 degrees from ceiling down for a wider reach. They are the preferred antenna for lower ceilings to cover a wider antenna than a Panel antenna. The Vertical Polorized Dome antenna radiates from the ceiling downward. Use to get the farthest reach downward. The Dual Polorized Dome antenna radiates downward and slightly upwards. Use to radiates above a ceiling. More Dome Antenna Information.

Building Mount Omni Directional Antenna

Wilson Building Mount Omni-Directional Antenna covers 800/1900MHz frequencies. It is omni-directional. If you are trying to boost the signal from several service providers where their towers are in different directions, this is the preferred antenna. If you are trying to cover one service provider tower, consider the higher gain Wilson Wide Band Directional Antenna. More Wilson Building Mount Omni Directional Antenna Information

Wilson Wide Band Directional Antenna

Wilson Wide Band Directional Antenna covers 700-2500MHz frequencies. It is directional and performs best when pointed toward your cellular providers tower. If you are trying to boost the signal from one service provider tower, this is the preferred antenna. If you trying to cover multiple service providers and their towers are in different locations, consider the Building Mount Omni Directional Antenna. More Wilson Wide Band Antenna Information

Cable Options

Wilson 75 Ohm RG-6 Quad Shield cable is recommended for repeater type system as it is low loss.

Connectors: Use 75 OHM F connectors which come on the AG Pro 70 amplifiers, cable and antennas.

About the Wilson Electronics AG Pro 70

Adjustable Gain

One challenge of in-building signal booster installation is getting enough separation between the inside antenna and outside antenna to prevent oscillation between the two antennas. Oscillation will prevent the system from working properly. In a small building, for example, that has a good outside signal, it may be difficult to get 50-75 feet of antenna separation required to prevent oscillation. With a Wilson adjustable gain amplifier, you can adjust the gain down.

The AG Pro 70 delivers a maximum gain of 70dB at 1900 MHz and 70dB at 800 MHz. The gain can be adjusted from 40db to 70db For 1900MHz frequencies and 35db to 65db for 1800MHz frequencies.

The AG Pro 70 also includes Wilson’s patented automatic oscillation and cell site overload protection, and proximity detection technologies to prevent interference on the cellular network. It works with all cellular devices on all North American service provider networks on 800MHz and 1900MHz frequencies (except Nextel/iDEN).

AG Pro 70 FEATURES

• Adjustable Gain Control
• Provides Reliable Signal
• Significantly Reduces Dropped Calls
• Increases Cellular Broadband Data Rates
• No Physical Connection to Cell Phone or Data Card Required
• Allows Multiple Phones & Cellular Data Cards to be used Simultaneously
• Oscillation (or interference) Detection & Automatic Shutdown with Auto Reset
• Overload Protection Circuit – protects cell towers from being overloaded
• Bi-directional Signal Booster Amplifies Send & Receive Signals
• Compatible with all cellular devices on all North American cellular networks (except Nextel/iDEN)
• Configurable with a variety of Wilson cellular antennas to fit virtually any building installation
• Extends battery life – Booster enables phone to work at reduced power
• FCC and IC type accepted

AG Pro 70 Specifications