Product Description
Build Custom 4G LTE Cellular Signal Booster System
The Wilson Electronics 4G LTE 700Mhz is an In-Building, dual band, cellular signal booster. It is an easy to install signal amplifier that is designed to provide a strong cellular signal inside mid sized buildings.
IMPORTANT NOTE: The Wilson 4G LTE 700MHz signal booster is made for the newer 700MHz frequency used by Verizon in some areas. In other areas Verizon will use 800MHz and/or 1900MHz which the this booster system will not boost. We have other booster systems for 800MHz & 1900Mhz frequencies. If you need help, call or use our contact form.
Outside Signal Strength Requirements:
The Wilson 4G LTE signal booster has been very effective in areas with a weak signal inside a building and a strong signal outside the building where the outside antenna is mounted. A fairly good signal is required outside the building to get optimum coverage area. If you need with the installation and coverage area calculation, contact us, describe the problem you're having along with location, provide the outside 700MHz 4G signal strength where the outside antenna is to be mounted, terrain, distance from tower, etc and we can help design your system and evaluate it's effectiveness. Also See: Estimating Coverage Area.
Select Equipment Required To Build Your Custom System
For a compete system installation, you'll need:
- Wilson 4G LTE Signal Booster
- 1 Inside Antenna - Panel Recommended
- 1 Outside Antenna - Wide Band Directional or Outdoor Panel Antenna Recommended
- Cable - Wilson 400 Low Loss Cable Recommended
Optional Accessories
- Wilson Lightning Surge Protector (Recommended )
- Signal Splitter(s) - For multiple Inside Antennas
- Wall Panel Door - In Wall Installation of Panel Antenna
READ: Calculating Coverage Area
Antenna Options
Wilson Panel Antenna
The Wilson Panel antenna is typically used as an indoor antenna and is wall mounted but can be ceiling mounted on higher ceilings (10ft or higher). They work well across longer, more narrow areas. Since they typically reach further, they are the prefered inside antenna. The Panel antenna radiates 70 degrees for a more focused beam to reach longer distances. 700 - 800mHz ... Gain: 5.2dbi. More Panel Antenna Information
Wilson Dome Antenna
The Wilson Dome Antenna is typically ceiling mounted. The Dome antenna radiates 360 degrees from ceiling down for a wider reach. They are the preferred antenna for lower ceilings to cover a wider antenna than a Panel antenna. The Vertical Polorized Dome antenna radiates from the ceiling downward. Use to get the farthest reach downward. The Dual Polorized Dome antenna radiates downward and slightly upwards. Use to radiates above a ceiling. 700 - 800mHz ... Gain: 3.3dbi.. More Dome Antenna Information.
Wilson Wide Band Directional Antenna
Wilson Wide Band Directional Antenna covers 700-2500MHz frequencies. It is directional and performs best when pointed toward your cellular providers tower. If you are trying to boost the signal from one service provider tower, this is the preferred antenna. If you trying to cover multiple service providers and their towers are in different locations, consider the Building Mount Omni Directional Antenna. 700-800 MHz - Gain: 7.3 dBi. More Wilson Wide Band Antenna Information
Wilson 13dbi Yagi Antenna
Wilson 13dbi Yagi Cellular Antennas are very effective at increasing your cell phone's signal strength in rural areas. The Yagi is a directional antenna and should be mounted above tree lines and pointed directly to your service providers nearest cell tower. 13dbi - 700-800MHz, 824-894MHz and 880-960MHz.. More Wilson Yagi Antenna Information
Cable Options
Wilson 400 Low Loss cable is recommended for repeater type system as it is low loss.
About the Wilson Electronics 4G LTE 700MHz Booster
Adjustable Gain
One challenge of in-building signal booster installation is getting enough separation between the inside antenna and outside antenna to prevent oscillation between the two antennas. Oscillation will prevent the system from working properly. In a small building, for example, that has a good outside signal, it may be difficult to get 50-75 feet of antenna separation required to prevent oscillation. With a Wilson adjustable gain amplifier, you can adjust the gain down.
The 4G LTE booster delivers a maximum gain of 70dB at 700 MHz. The gain can be adjusted from 40db to 70db.
The Wilson 4G LTE booster also includes Wilson’s patented automatic oscillation and cell site overload protection, and proximity detection technologies to prevent interference on the cellular network. It works Verizon 4G LTE network.
4G LTE Booster Features
- Adjustable Gain Control
- Provides Reliable Signal
- Increases 4G LTE Broadband Data Rates
- No Physical Connection to Cell Phone or Data Card Required
- Allows Multiple Phones & Cellular Data Cards to be used Simultaneously
- Oscillation (or interference) Detection & Automatic Shutdown with Auto Reset
- Overload Protection Circuit – protects cell towers from being overloaded
- Bi-directional Signal Booster Amplifies Send & Receive Signals
- Compatible with Verizon 4G LTE
- Extends battery life – Booster enables phone to work at reduced power
- FCC and IC type accepted
4G LTE 700 Specifications
|
Product Number
|
801865
|
|---|---|
|
Frequency
|
Up-link 776 - 787 MHz / Down-link 746 - 757 MHz
|
|
Gain
|
70 dB / 70 dB
|
|
Max Up-link Power
|
28.7 dBm
|
|
Max Down-link Power
|
25.5 dBm
|
|
Noise Figure
|
3.5 dB nominal / 5 dB nominal
|
|
Flatness
|
|
|
Power Requirements
|
110-240 V AC, 50-60 Hz, 10 W
|
|
Connectors
|
N-Female
|
|
Dimensions
|
5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm)
|
|
Weight
|
1.27 lbs (0.544 kg)
|
Additional Information
| SKU | AK801863 |
|---|---|
| Brand | Wilson Electronics |
| Model | N/A |
| Connector Type | N Female |
| Frequency Range | Up-link 776 - 787 MHz / Down-link 746 - 757 MHz |
| Gain | No |
| Antenna Category | Amplifier Kits |
| Accessory Type | Signal Improvement |
| GTIN | No |
| Compatible Devices |
|
You have no items to compare.
